Buzz World 365 Logo

Mülltonneneinhausung DIY | Teil 2

Aug 30, 2022

Mülltonneneinhausung DIY | Teil 2

so now finally comes the second part about the trash can enclosure, many of you have probably seen the first dog because that was three months or even more ago that I did it, now comes the second part, yes I'm not here, TRUE? now the trash can enclosure is because I wanted to say a few words about it first, namely the fact that the project was somehow not easy for me, it was kind of a project that was always a bit difficult, no idea , and then some things that worked out the way I wanted and so on that's why it was always a bit but never really that you did a bit and we know what was done, some fully filmed also considered if I should do it and then post again, now decided to do it so there's also the first domestic one for quite some time and now comes the second part Like I said I didn't film some things so I would say we go to the trash cans in a house and finally we're done and I'll talk about some things and then I'll show you the construction of things.
m lltonneneinhausung diy teil 2
I filmed, so I have the doors and everything that was filmed. I'll show you there and the next project will run normally again. Yes, in a way it was a sonja. Do you know something like that? the really bad stuff definitely wants that doesn't work that way, but now it's finally finished and we'll go there with a little bit of wind. I hope you understand me well. there's another big difference is i just didn't finish it in one piece but that will certainly adjust over time so we'll take a look at the whole e in a little more detail like i said i still did the doors and it would be the building.
m lltonneneinhausung diy teil 2
I'll show you that at one point I got stuck here in the back. I found out I have to build this scary crossbar. back because without it the whole thing won't really hold up to the roof maybe and I didn't film anything there's just a tow plate on it a resin mill plate and around the outside is this and on top we did like this and i did it so everything can be planted is all now it rains a little in Braunweiler our we say we put it there there is no drain or anything back there but it just puts here in the corner there are a couple of seats 12 here you can see better that way and there on the other side sometimes some and they hold everything together first i thought if i have to put the language carrier here so i don't wobble here but that's really easy. works great just a simple frame its nothing more so its a very simple thing what i didnt gain is these small parts here in the middle i also did them afterwards like i said just let go so the optics fit everything its still a one little unstable I have to tighten one or the other which is sometimes a little uncomfortable that prevents me from putting two screws here maybe everything also gives me the fact that somehow d3 rhymes if we clamp it all or screw it maybe from behind the book i have no idea time will tell how i do it i am glad one day we will do it all is yes the doors as i said i can see them they are in the video i filmed everything also worked great actually it was flawless really great on the door, these are adjustable stalls.
m lltonneneinhausung diy teil 2
I can absolutely recommend most of the advertising though I, yeah it's not sponsored but these are exotics adjustable door hardware so tech can set them here and then you can adjust the height here so for example this lock fit very well in the end it was so I had these the accessories are embarrassed but a little because they are not optimal so I'm already looking forward to it but the counterpart here here the case I did it myself because what I needed so far has a little more away from the original these are kind of narrow like the middle part here and so you can move through that I don't even know because it's a hundred percent solid and it had worked so far it was always like that after something didn't it fit so good we can do it real good let's make it adjustable parts then it all held up and about three days later it all fell out again so i have it here now little done from the side of a movie, you can see it pretty much like here, more or less play and then everything can move a little bit more round and that sounds but something, so it's perfect against you because it falls over here.
m lltonneneinhausung diy teil 2
It can wobble back and forth a bit, but there's absolutely no problem because doors are usually hard to fit through the hinges, so that's good, and actually, it's almost always too hot, but like I said, somehow I didn't bake it the build is finally done and I'm going to show you how I'm going to install it and I wish you a lot of fun with the video and as I said in the next video there will be normal videos again with normal projects or CNC or whatever you know about me Take a look at everything and like I said everything else that is installed is linked in the video and the plans if you have someone with you to rebuild they are already on the home page I will also link you to continuation and yes then until the next videos it's ok now it should be here for a long time you've been famous watched how i do it best so this wattenscheid division fits now finally it's like this q So we've basically done two areas again this here's the one that goes back here between when I build doors or when I build backwards so you can keep the distances we actually made a second adapter that's a little thinner and easier to swap out because we never really but i had two adapters from factory or second jig let's say it comes here on the front or here on the back and keeping the distance even and with that i can put everything together relatively quickly yeah now look at the part again and there's the second door and so on and so on to give everything a little more stability like you the screws I screwed in here now I have jet recently decided to screw the long screws of the 100 screws again at an angle and bark them back into the permanent bark or wood so that everything holds up a little better, it certainly won't damage the second door. is it particularly important that the protractors the diagonal comes in the support it does not go the same way but in the other direction because it is the other side that is attached to the other side very important or I want to distribute the time that I have here I made a mark immediately so I know that you have to go here you never know exactly how i do everything now but i just saw it done in the first division and yeah after that comes the door assembly and i would say it ties me to the assembly now
m lltonneneinhausung diy teil 2
Trending