UNNÖTIG- Tausendfache Retouren von Schweißgeräten! Schlauchpaket wackelt?
such rubbish you buy a new one with a max welding machine then you connect the euro central connection for the first time and it wobbles that wobbles that can't be true if you had spent 200 300 euros more then you would have gotten something reasonable you can do that tighten the whole thing again you can unscrew the whole thing again maybe you tilted it in some way the first time you put it on that can of course always be the case but then you are sure because you bought really junk the whole thing can't be tight if it wobbles the whole thing can't function properly in the long run there must either be a fault somewhere in the component or the euro centrally mounted incorrectly what do most of them do from now on its residue label and then the device goes back and that's definitely not only one device we have already written to so many people about it there are really a lot of devices and that is of course extreme it's a shame because if you take a closer look at the whole thing you'll notice that there's even a little bit that the whole game has it's definitely not a mistake because the thing annoys me we'll just watch the whole thing in this video and if in the future you call the shaky euro central connection or the cover behind it is shaky then you know exactly that is definitely not a mistake and i also showed you how you can check the whole thing to see if everything is really tight but just take a look at it a little bit of detail we have the euro central connection here and that's really a wonderful invention because it doesn't matter whether my max welding machine like this one costs 200 euros or 2000 euros if the euro central connection is connected then the whole thing fits I have 2 front taxes here pins the wire goes through there the protective gas goes through and of course I find the whole thing again on the euro central connection on my device sees m here, for example, the protective gas next to these two pins goes down below switzerland stepped through or switzerland stepped through promoted now i can of course first measure in this screw connection maybe it was already done wrong somewhere and now i can see at the screw connection I have a depth of 11 and when I measure the union nut on the welding machine, the whole thing is pulled up really nice, of course it's important that I can then measure down, then I have about ten millimeters there, that means I really have there another millimeter and millimeter is really a lot so strong i can't buckle this screw connection that it wouldn't be enough that it causes the wobbling somewhere so that's the first little thing that i can say about the union nut on the It can't be screwed, but of course I can do it sometimes, just use another hose pack et try it out so I have about 10 15 Mack hose packages accordingly I can of course take one where I have another device where nothing wobbles at all on the device and if I connect this here then it will fit right away this is for example a larger one hose package that can do more power more temperature from that is 1 mb 24 hose package so a very nice thing you can really throw 220 amps if I put the whole thing here then I notice right away that it wobbles very minimally but it was true of course not remotely as strong as the previous original hose package from this parkside welding machine that means it is probably due to the hose package the hose package is rubbish if I give a little push here but just as an example no skin his welding machine probably but sometimes you bump into one another, sometimes there, you can see everything always goes straight to this device via that it's also a bit of a riddle or the solution to the riddle unscrew the whole thing again then I can screw on an original hose package again and then we can explore it further now let's do the following it's just a plastic cover at the front a protective cover that we can simply pull down to the back and then we can remove one side of it and then you can wiggle again and then you can see that the whole wiggle is the solution to the riddle that the whole wiggle is actually just this plastic cover and depending on which side you watch it from you can see it very very well i always write that to people but the people we believe that they always don't say that i can't be no that's hanging there that's not right and that it's wobbling even a certain sense if you think about it a little more closely we just had a bit of a grudge against our welding machine gen hewn and you saw relatively clearly that everything always went straight to the welding machine to the euro central connection and now I have a certain crumple zone here, that means I have a certain bollard here that always starts off like this and I believe that there is a deeper lisa meaning behind it, that you just allow a bit of play, that it also makes sense to have a bit of play, that means if you are unsure about your welding machine, then simply unscrew it here or that it's just put over here and then twisted so you can check that within a minute and then you really see and if you offer it like this now it has a bit of play at some point the movement goes or this of course also bumps into the welding machine again but not as easy as with a device where the whole thing is really extremely well-designed we can even look at the whole thing in detail look at this if you twist this union nut a bit here then you see there is a screw, a cross screw that we can simply unscrew and with that we can pull back this complete plastic cover and then you can really look at it again, that the whole thing is really, really good fits like that that means the whole thing is basically from my point of view everyone can judge for themselves but it's really not a mistake it's just this plastic cover that has a bit of play that wobbles you saw because of it even makes it to a certain extent way sense that the whole thing has a bit of play that the whole thing wobbles that not every hit goes straight to this euro central connection what really annoys me about this thing that is not manufacturer-specific there are different manufacturers of these devices on offer with the devices Where the hose packages are there, they have that shape, there are other hose packages totally died but as I said it's annoying that so many devices are always going back i don't want to know how many devices parkside alone has gone back and i don't want to know what happens to these devices which are really checked again and sold again i can I often can't imagine it at all.
I think of this Amazon story with these huge things that are then there somewhere. I don't know if someone has a b ware shop at the time or has information. They can write it in the comments and you can see it here again how sensibly the whole thing is put on the union nut as I said from the win the gentleman still has a little space then and until it really closes and accordingly you can really tighten it very, very tightly here and it's really just this plastic cover for those who are unsure who can really invest 23 minutes, can unscrew the whole thing, can then do the whole thing in det look at ail i explain that really a lot of people write an extra text and a lot of people don't believe me then send their device back anyway and say no it wobbles i don't want it because of that so as i said it's an unnecessary thing annoys me that's something everyone always talks about people of sustainability if i were a manufacturer of welding devices i would put it with every device after the tenth return at the latest or would send a little information about it i hope this video provides a bit of enlightenment i will screw the whole thing back together again for a moment and while I'm watching I'll link a few nice videos at the end.
You're welcome to watch them too. I wish you a lot of fun welding the device and a few other devices I'll link under the video until then your money